Skip to content
application note

Blowroom Magnets in Spinning Mills: Cutting Fire Risk

A bale hoop or nail hitting a beater can start a fire that travels through the ducting. Here is how blowroom magnets work, where to fit them, and why they work best alongside other protection.

Latif Engineering3 min read

Fires in spinning mills often start in the blowroom. Cotton fibre burns easily, the air is full of fine lint, and there are beaters and openers turning at high speed. All it takes is one piece of iron hitting a beater to throw a spark, and the air stream carries the burning fibre straight down the duct to the next machine.

A blowroom magnet removes much of that iron before it reaches the beaters. It is not the only protection a mill needs, but it is one of the simplest.

Where iron in cotton comes from

  • Bale hoops and wire that break or are not fully removed when bales are opened.
  • Nails, bolts and small hardware picked up during ginning, storage and transport.
  • Pieces from machines such as broken pins and lattice parts.

What it causes

Fire

A spark from iron striking a beater can ignite cotton. The fire is then carried by the air stream, which is why blowroom fires can spread so quickly through ducting into other machines.

Machine damage

Iron damages beater blades, opener pins, and further down the line it can damage card clothing on the licker-in and cylinder, which is expensive to replace.

How a blowroom magnet works

A blowroom magnet is a section of duct with strong permanent magnets in its wall, usually in a curved hump or behind a flat plate. As cotton moves through the duct in the air stream, iron pieces are pulled out of the fibre and held against the magnet face. The face is smooth so cotton slides past and does not collect on it.

A door in the side lets the operator remove the collected iron at set times during the shift.

Where to fit it

The usual position is in the duct just after the bale opener and before the first cleaner or beater. This is where the cotton has been opened enough for iron to be pulled free, and before it meets the first high-speed machine.

Mills with long ducting or several lines sometimes fit a second magnet before the cards.

A magnet is one layer, not the whole answer

Magnets catch iron and ordinary steel. They do not catch stainless steel, brass, aluminium, stones or other heavy objects, and they cannot put out a fire. Good blowroom protection usually has several layers:

  1. Careful bale opening, with all hoops and wire removed and counted.
  2. A heavy particle separator to drop out stones and heavy pieces.
  3. A magnet to remove iron.
  4. A metal detector to catch other metals.
  5. Spark detection and extinguishing in the ducting.

Each layer catches what the others miss.

Keeping the floor clean too

Hoops, nails and wire also end up on the floor around the bale lay-down area, and from there they get picked up with loose cotton. A magnetic sweeper run over the floor once a shift keeps that area clean.

Maintenance

  • Clean the magnet at fixed times every shift and record what was found.
  • Check that the door seals properly so the duct does not leak air.
  • Do not let lint build up on the magnet face. It can hide iron and reduce the pull.
  • Check the magnet strength once a year.

Waste and recycling lines

Lines that open and recycle cotton waste and textile waste carry even more iron than virgin cotton, because the material has been handled more. These lines need a magnet at least as much as the main blowroom.

Tell us your duct size and shape and where you plan to fit it, and we will make the magnet section to suit. Request a quote.

Frequently asked questions

Does a blowroom magnet prevent all fires?

No. It removes iron, one common cause. Mills also need metal detection, spark detection and careful bale opening.

Where is a blowroom magnet installed?

Usually in the duct just after the bale opener and before the first beater.

Will cotton build up on the magnet?

A smooth magnet face lets cotton slide past. Lint should still be cleared when the magnet is cleaned.

WhatsApp us