Why Sugar Mills Fit Magnets Before the Cane Shredder
During crushing season, one stoppage costs more than the magnet. Here is where iron comes from in cane, what it damages, and where sugar mills place magnets from the carrier to the packing hall.
A sugar mill runs flat out for a few months a year. Every hour lost during the crushing season is cane that is not crushed, and cane that waits loses sugar. That is why mill engineers take tramp iron so seriously. A single piece of steel in the wrong place can stop the mill house.
Where the iron comes from
Cane travels a long way before it reaches the carrier. On the way it collects iron:
- Broken parts from trolleys, trucks and tractors.
- Pieces of cutting tools and harvesting equipment.
- Chains, hooks and wire used to tie loads.
- Bolts and parts from the yard, cranes and feeder tables.
What it damages
Knives and shredder
Cane first meets the leveller and cutter knives, then the shredder. A piece of steel hitting cane knives or shredder hammers at full speed can break them, and broken pieces then travel on as more tramp iron.
Mill rolls
Iron reaching the mill tandem can damage roll grooves. Mill rolls are large and costly, and repairs take time.
Carriers and conveyors
Long pieces of steel can jam between slats and the frame of the cane carrier, bending slats or breaking chain.
Where to place magnets
Over the cane carrier, before the shredder
This is the most important magnet in the mill. The cane bed on a carrier is deep, so the magnet must reach a long way down. That is why most mills use a strong electromagnet here, either an electro suspension magnet or a self-cleaning overband electro magnet. The usual position is after the knives, where the cane bed has been levelled and opened up, and before the shredder.
On the bagasse conveyor
Bagasse goes to the boiler. Iron in it can damage boiler feeders. A suspension magnet over the bagasse conveyor is low-cost protection.
In juice, syrup and molasses lines
Iron particles from wear in pumps and pipework end up in the liquid. A liquid trap magnet in the line catches them before they reach evaporators, centrifugals or the finished product.
Before sugar packing
Refined sugar must be free of metal. A drawer magnet with neodymium tubes in the chute before the packing machine is the final check, usually alongside a metal detector.
Electro or permanent over the carrier?
The deep cane bed makes this one of the few places where an electromagnet is often the better choice, because it can reach further. But a mill should plan for power interruptions: if the magnet loses power, what it has collected can fall back onto the carrier. An interlock that stops the carrier when the magnet trips is worth having.
Prepare in the off-season
The off-season is when magnets should be inspected:
- Check coil insulation and the rectifier on electromagnets.
- Check the belt, bearings and drive on overband magnets.
- Measure field strength at the face with a gauss meter.
- Check the suspension height. Over time, magnets are sometimes raised to clear obstructions and never lowered again.
- Clean drawer and liquid magnets and replace any damaged tubes.
Summary
- Strong magnet over the carrier, after the knives and before the shredder.
- Magnet over the bagasse conveyor.
- Liquid trap magnets in juice and syrup lines.
- Drawer magnet and metal detector before packing.
- Off-season inspection of every magnet.
If you send us your carrier width, cane bed depth and the height available above it, we can size a magnet for your mill. Request a quote.
Frequently asked questions
Where should the magnet go on a cane carrier?
Usually after the knives and before the shredder, where the cane bed is level and open.
Why do sugar mills often use electromagnets?
The cane bed is deep, and an electromagnet can reach further into it.
When should sugar mill magnets be serviced?
During the off-season, so they are ready before crushing starts.
Equipment mentioned in this article
Cane Cutter Knives
Replacement knife sets for cane leveller and cutter shafts, made from tough steel with hard-faced edges so they stay sharp through the crushing season.
ViewDrawer Magnet
A dust-tight housing with two or three rows of magnetic tubes that slide out like drawers, fitted in-line on gravity chutes carrying powders and granules.
ViewCane Carrier
A heavy-duty slat conveyor built with steel slats on strong chains, carrying cane from the feeder table through knives and shredder to the first mill.
ViewElectro Suspension Magnet
A stationary electromagnet suspended over a conveyor or chute, giving stronger and adjustable field strength than a permanent suspension magnet for manual or scheduled clean-out lines.
ViewLiquid Trap Magnet
A pressure-rated housing with magnetic rods inside, fitted in a pipeline to remove iron particles from oils, syrups, chemicals, paints and slurries.
ViewOverband Electro Magnet Separator
A suspended, powered magnet mounted crosswise or in-line over a conveyor that lifts and continuously discharges large ferrous tramp metal out of the material stream.
View