Magnetic Drum Separator on a Conveyor: Where It Goes and How It Works
A magnetic drum separates iron from bulk material without anyone touching it. Here is how the drum works, where it sits on a conveyor line, and how it differs from a magnetic pulley.
People search for this machine under many names: magnetic drum, drum magnet, magnet drum for conveyor, even drum motor magnet. They usually mean the same thing: a turning drum that pulls iron out of a stream of material and drops it somewhere else, all on its own. This article explains how it works and where it belongs on a conveyor line.
How a magnetic drum works
A magnetic drum has two main parts:
- A fixed magnet inside, covering part of the circle, usually around a third to a half of it.
- A rotating shell of stainless steel around the magnet, driven by a motor and gearbox.
Material is fed onto the drum from above. Non-magnetic material falls off the front in its natural path. Iron is held against the shell by the magnet and carried round with it. When it passes the end of the fixed magnet, it lets go and falls behind a divider plate, called a splitter, into a separate chute. Nothing has to stop and nobody has to clean it.
Where it sits on a conveyor line
A magnetic drum is normally fitted at a transfer point, where material leaves one conveyor and falls to the next process. There are two common layouts:
- Fed from a chute: material falls off the end of the conveyor into a short chute that spreads it across the drum face.
- Fed by a vibrating feeder: used where the material needs to be spread thinly and evenly, for example in recycling or for fine particles.
Either way, the drum should be at least as wide as the stream of material, and the feed should be spread evenly across its face.
Drum separator vs magnetic pulley
This is where most confusion comes from, because both look like a round magnet at the end of a belt.
- A magnetic pulley replaces the head pulley of the conveyor. The belt wraps around it, so it acts through the belt.
- A drum magnetic separator is a separate machine below or after the conveyor. Material touches the drum shell directly.
A pulley is cheaper and saves space. A drum gives a cleaner separation, because the material falls directly onto the magnet in a thinner layer, and it can be sized and adjusted on its own.
Electro or permanent?
An electro magnetic drum separator uses a DC coil. Its strength can be adjusted, and it can reach deeper into thick layers of material. It needs a power supply and a rectifier.
A permanent magnetic drum separator uses ferrite or neodymium magnets. It needs no power for the magnet, only for the drive motor, and keeps working at full strength during a power cut. For most bulk handling jobs in Pakistan this is the more practical choice.
Where magnetic drums are used
- Recycling: pulling steel out of shredded scrap, municipal waste and e-waste.
- Foundries: cleaning iron from return sand.
- Steel slag: recovering iron from crushed slag.
- Feed and grain: removing iron from free-flowing material at high tonnage.
- Minerals: cleaning or concentrating dry minerals. For slurries, a wet drum magnetic separator does the same job in a tank.
How it is sized
We need to know four things:
- Tonnage per hour.
- Width of the material stream.
- Particle size, from fines to large lumps.
- What kind of iron you want to remove or recover.
Tonnage and particle size decide the diameter. Stream width decides the face width. The type of iron decides whether ferrite, neodymium or electro is right.
Looking after a drum separator
- Check the splitter position now and then. If iron ends up in the clean product, the splitter often needs a small adjustment.
- Watch the shell for wear on abrasive material. A worn shell can be replaced or given a wear lining.
- Keep the feed even. A drum fed only on one side does half the work.
Not sure whether you need a drum, a pulley or an overband? Send us a photo of your conveyor and the material, and we will tell you what fits. Request a quote.
Frequently asked questions
What is the difference between a magnetic drum and a magnetic pulley?
A magnetic pulley replaces the conveyor head pulley and works through the belt. A magnetic drum is a separate machine that material falls onto directly.
Does a magnetic drum need cleaning?
No. The rotating shell carries iron past the magnet and drops it automatically.
Can a magnetic drum work with wet material?
For slurries, use a wet drum magnetic separator, which runs in a tank. Dry drums suit dry or damp bulk material.
Equipment mentioned in this article
Drum Magnetic Separator
A rotating drum separator available in electro or permanent configurations, providing continuous ferrous removal at the head pulley of a conveyor.
ViewElectro Magnetic Drum Separator
An electrically-powered rotating drum that pulls tramp iron and ferrous fines out of bulk material on a conveyor, protecting downstream crushers and mills.
ViewWet Drum Magnetic Separator
A magnetic drum running in a tank of slurry, used to recover magnetite or to remove iron-bearing particles from mineral and ceramic slurries.
ViewMagnetic Pulley
A magnetised conveyor head pulley that separates ferrous tramp metal from material as it discharges, without needing a separate drum unit.
ViewPermanent Magnetic Drum Separator
A rotating drum fitted with a fixed array of high-energy permanent magnets that removes ferrous contamination from bulk material without needing an electrical connection.
View