Skip to content
guide

How to Protect a Crusher from Tramp Iron

One excavator tooth can stop a crusher for a day. This guide explains which magnets protect jaw, cone and hammer crushers, where to mount them, and the mistakes that let iron through.

Latif Engineering4 min read

Ask anyone who runs a stone crushing plant or a cement raw material line what stops their crusher most often, and tramp iron will be near the top of the list. A broken excavator tooth, a drill bit, a length of rebar or a loose liner bolt goes in with the feed and comes out as a damaged jaw plate, a cracked mantle or a ripped belt.

The good news is that most of it can be stopped before it reaches the crusher. This guide explains how.

What tramp iron actually does

  • Jaw crushers: uncrushable steel can crack jaw plates and overload the toggle plate.
  • Cone crushers: tramp iron is a common cause of mantle and concave damage, and frequent tramp release events wear the release system.
  • Hammer and impact crushers: hammers and blow bars can break, and a broken hammer then becomes tramp iron itself.
  • Conveyor belts: a long piece of steel can jam at a transfer chute and slit a belt along its length in minutes.

The repair is only part of the cost. The bigger loss is the lost production while the plant stands.

Where tramp iron comes from

In quarries: bucket teeth and adaptors, drill bits and rods, and pieces of screens. In cement plants: liner bolts, chain links and maintenance tools left in hoppers. In coal handling: roof bolts and mine hardware. In recycling: almost anything.

The main options

Overband magnet (self-cleaning)

An overband electro magnet separator hangs above the conveyor and has its own small belt running around the magnet. Iron is lifted out of the burden and carried off to the side, all the time, without anyone stopping the line. This is the usual choice for continuous plants with deep burden and regular tramp iron. Where there is no reliable power supply for a large coil, an overband permanent magnet separator does the same job without electricity for the magnet.

Suspension magnet (manual cleaning)

A suspension magnet is a fixed magnet without the cleaning belt. It holds the iron until someone switches it off or slides it aside to clean it. It costs less and suits lines where tramp iron is occasional. A permanent suspension magnet needs no power at all; an electro suspension magnet reaches deeper into the burden.

Magnetic head pulley

A magnetic pulley replaces the head pulley and pulls iron down against the belt as material discharges. It is compact and simple, but it works from below, so it is best with shallow burden.

Metal detector

Here is a point many plants miss: excavator teeth are often made of manganese steel, which is only weakly magnetic. A magnet may not lift it. A metal detector on the belt finds it and stops the conveyor or marks the spot. The safest crushers have a magnet first and a detector after it.

Where to mount the magnet

An overband magnet can be mounted in two ways:

  • In-line, over the head pulley. As material leaves the belt it loosens and spreads, so iron is easier to pull out. This is usually the most effective position.
  • Cross-belt, over the conveyor. The magnet sits across the belt along its run. It is easier to fit on existing conveyors but must work through the full depth of a packed burden.

Whichever you choose, mount it before the crusher feed chute, not after it.

What decides the size

  1. Belt width, so the magnet covers the whole stream.
  2. Burden depth, which sets the suspension height and how strong the field must be.
  3. Belt speed, because faster belts give the magnet less time.
  4. The biggest and smallest pieces of iron you need to remove.
  5. Material, especially if it is wet, sticky or very abrasive.

Common mistakes

  • Mounting the magnet too high. Field strength drops quickly with distance. A few extra centimetres can halve the pull.
  • Never cleaning a suspension magnet. A loaded magnet lets new iron pass, and can drop the whole load back onto the belt.
  • Steel structure too close to the magnet. Steel idlers, chutes and frames near the magnet face steal its field. Use stainless or non-magnetic parts in the magnet zone.
  • Relying on a magnet alone for manganese steel. Add a metal detector.

If you send us your belt width, belt speed, material and the kind of iron you are finding, we will size the magnet for your conveyor. Request a quote and an engineer will help.

Frequently asked questions

Why does my magnet miss excavator teeth?

Many bucket teeth are made of manganese steel, which is only weakly magnetic. Add a metal detector after the magnet.

Overband or suspension magnet for a crusher?

An overband cleans itself and suits continuous plants with regular tramp iron. A suspension magnet costs less and suits lines with occasional tramp iron.

How high should the magnet hang above the belt?

As low as the burden safely allows. The exact height is calculated from burden depth, belt width and magnet strength.

WhatsApp us